ACCESSORIES FOR CIRCULATORS |
| CATALOG # |
ITEM
DESCRIPTION |
| 4-300040 |
Lab Algicide
A general purpose lab
algicide that helps keep water baths clean, odor free, and resistant to
black algae. Stainless steel compatible. Use 10-15 drops/gal. to prevent
algae growth. 8 oz.dispenser bottle treats approximately 400 gal. |
| 4-300050 |
A concentrated
liquid for cleaning, removing rust & mineral deposits from stainless
steel and plastic baths. For best results, use at elevated temperatures.
Helps remove existing algae prior to treatment with Lab Algicide. 1 oz.
treats approximately 2 gal. |
| 040250 |
Model 20 Bath
Cooler 120V, 60Hz |
| 040251 |
Model 20 Bath
Cooler 240V, 50Hz |
| 050300 |
Cooling coils for
immersion circulators Model 71 and 7306.
The stainless steel coil, when connected to a water source, permits more
rapid cool down from high temperatures or better control when operating
close to ambient temperatures. Not recommended for use in circulator
baths where fluid temperature exceeds boiling point of water. For high
temperature cool-down, we recommend PolyScience Model 20. |
| 060300 |
Cooling coils for heating circulators |
| 060301 |
Hollow Plastic Floating Balls - 3/4 in. (20mm) diameter, Pack of 400
Create a blanket of insulation in any open bath, reducing heat loss 75%
and evaporation by 87%. Reduce fumes and splashing hazards. Usable to
temperatures to 110°C and in most bath fluids. Made of polypropylene. |
| 060304 |
Tubing Clamp for 3mm to 13mm tubing |
| 060305 |
Brass Reducing Adapters, 8mm I.D. (Set of 2) |
| 060306 |
Brass Reducing Adapters, 3mm I.D. (Set of 2) |
| 060307 |
Buna
N Tubing, 5/16 in. (8mm) I.D. per yard (.9m) |
| 060308 |
Buna
N Tubing, 1/2 in. (13mm) I.D. per yard (.9m) |
| 060309 |
Insulation for 5/16
in. (8mm) tubing per yard (.9m) |
| 060310 |
3
ft. (.93m) flexible Teflon® lined, stainless steel overbraid tubing with
1/4 in. NPT quick connects at both ends. Maximum temperature use 300°C. |
| 060311 |
Insulation for 1/2 in. (13mm) tubing per yard (.9m) |
| 060312 |
Low
Temperature Insulated Tubing - 6 ft. (1.9m)
Minimizes temperature loss from a circulator to external device. 6 ft.
(1.9m) of 1/2 in. (1.27cm) I.D. Buna N tubing with foam insulation. |
| 060314 |
Tube, Hose Barb ¼ MPT to 13mm Brass (set of 2) |
| 099590 |
Thermometer, Glass, -20°C to 150°C |
| 510-011 |
Circulator Adapter Kit
Contains (3) nylon fittings; ¼, 3/8, 3/16 barb x ¼ MPT
|
BATH
FLUIDS
Low Temperature -
Dynalene® HC-50 combines the low temperature performance of synthetic
organic and silicone fluids while extending the properties of familiar
aqueous based glycols. Excellent low temperature performance without
toxicity or risk to the environment, equipment or personnel.
High Temperature - Dow Corning® silicone heat transfer fluids provide
superior thermal stability over their temperature ranges. Check bath
system compatibility before using. Compatible with stainless steel,
not compatible with Buna or natural rubber.
| |
Temperature
Range |
Freeze Point |
Viscosity |
Quantity |
Cat No |
| Dynalene® HC
50 |
-53° to 60°C
-63° to 140°F |
-56°C
(-68°F) |
@0°C 3.6 cSt,
@-40°C 15.1 cSt |
1 gallon |
060330 |
| Dow
Corning® 510 |
50° to 150°C
122° to 302°F |
-70°C (-94°F) |
@25°C 50 cSt |
1 gallon |
060326 |
| Dow
Corning® 550 |
100° to 200°C
212° to 392°F |
-50°C (-58°F) |
@25°C 125 cSt |
1 gallon |
060327 |
| Dow
Corning® 710 |
150° to 250°C
302° to 482°F |
-22°C
(-7.6°F) |
@25°C 500 cSt |
1 gallon |
060328 |
*Due to high viscosity, Silicone fluids 510, 550 and 710 are not recommended for use below 90°C.
*Dow Corning fluids are produced by and registered TMs of Dow Corning Corporation. Dynalene HC is a registered TM of Advanced Fluid Technologies, Inc.
